| Part Number |
| MBD-X7DCA-L-O |
X7DCA-L-O(Standard Retail Pack) |
| Physical Stats |
| Form Factor |
Micro ATX |
| Dimensions |
10" x 10 " (25.4cm x25.4cm) |
| Processor/Cache |
| CPU |
Dual 771-pin LGA Sockets
Supports up to Dual Intel® 64-bit Xeon®processor(s) of the same type below:
- Quad-Core Intel®
Xeon®Processor
5400/5300 sequence
(Harpertown
/Clovertown processor)
up to 3.16 GHz
- Dual-Core Intel®
Xeon®Processor 5200/5100/5000
sequence (Wolfdale
/Woodcrest/Dempsey processor) up to 3.40 GHz
|
| System
Bus |
1333 / 1066 MHz system bus |
| System Memory |
| Memory
Capacity |
Six 240-pin DIMM sockets
Supports up to 48GB 667/533MHz DDR2 ECC Register SDRAM
Dual channel memory bus
|
| Memory
Type |
667/533MHz Register DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes |
512MB, 1GB, 2GB, 4GB, 8GB** |
| Memory
Voltage |
1.8V |
| On-Board Devices |
| Chipset |
Intel® 5100 (San Clemente) chipset
Intel® ICH9R |
| SATA |
Intel ICH9R SB SATAII Controller
RAID 0, 1, 5, 10 support (Windows only)
RAID 0, 1, 10 support (Linux) |
| Network Controllers |
Dual Intel® 82573L Single Port Gigabit Ethernet Controller
Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output |
| Graphics |
XGI Z9s with 32 MB of DDR2 memory |
| Audio |
High Definition 7.1 Channel Audio |
| Super I/O |
Winbond 83627DHG chip |
| Clock Generator |
ICS9LPR501 chip |
| Input / Output |
| Serial
ATA |
Six Serial ATA ports
Six SATA hard drives supported
|
| Audio |
High Definition 7.1 Channel Audio
Line-in / Line-out / Microphone Ports
|
| Floppy |
1 Floppy controller; 1.44 MB |
| USB |
4 rear + 2 Type A connectors + 1 headers (2 Ports)
8 total USB ports, 2.0 Compliantt
|
| VGA |
1x VGA Port |
| Floppy |
2x RJ45 LAN ports |
| Serial Port / Header |
1 Fast UART 16550 serial port
1 header
|
| Chassis ( Optimized for
X7DCA-L ) |
| Mid Tower |
CSE-733TQ-645
CSE-733TQ-465
CSE-733T-645
CSE-733T-465
CSE-733T-450
CSE-733i-645
CSE-733i-450 |
| Tower / 4U Rackmount |
CSE-743T-645
(FAN-0091, CBL-0088 Required)
CSE-743i-645
(FAN-0091, CBL-0088 Required)
CSE-742T-650 |
| Important Chassis Notes |
To ensure system stability, a 500W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
|
| Expansion Slots |
| PCI-Express |
1 (x16) PCI-e slot
1 (x8) PCI-e slot
1 (x4) PCI-e (using x8) slot
|
| PCI |
1x 32-bit 33MHz PCI (5V) slots |
| System BIOS |
| BIOS
Type |
16Mb SPI Flash with Phoenix ® BIOS |
| BIOS
Features |
Plug and Play (PnP)
DMI 2.3
PCI 2.2
ACPI 1.0/2.0/3.0
USB Keyboard support
Hardware BIOS Virus protection
SMBIOS 2.3
|
| Management |
| Software |
Super Doctor
III
Watch Dog
NMI |
| Power
Configurations |
ACPI Power Management
Main Switch Override Mechanism
Wake-On-Ring (WOR) header
Wake-On-LAN (WOL) header
Power-on mode for AC power recovery
Internal / External modem remote ring-on |
| PC Health Monitoring |
| CPU |
Monitors for CPU Cores,+1.5V, +3.3V, +5V, ±12V, +5 Stdby, VBAT
CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
| FAN |
Six 4-pin fan headers
6x fans with tachometer monitoring
Status monitor for speed control
Status monitor for on/off control
Support for 3-pins (w/o speed control)
Low noise fan speed control
Pulse Width Modulated (PWM) fan connectors
|
| Temperature |
Monitoring for CPU and chassis environment
CPU thermal trip support
Thermal Control for 8x fan connectors
PSU I2C temperature sensing logic
Thermal Monitor 2 (TM2) support
PECI |
| LED |
CPU / System Overheat LED
Suspend-state Indicator LED
+5V Standby alert LED
|
| Other
Features |
Chassis Intrusion Detection
Chassis Intrusion Header
|
