| Jetway NF632E 3.5" SBC Motherboard |
| Processor | Intel® Core i5-7300U, 2.60GHz – 3.50GHz Burst, 2-Core 4-Thread, 15W TDP, vPro
* Ships with passive heatsink installed for bench testing |
| Memory | 2 x 260-pin SODIMM un-buffered Dual Channel DDR4-2133 up to 32GB Total |
| Graphics | Intel HD Graphics 520, 300MHz - 1.0GHz |
| Audio | Realtek ALC662VD HD Audio |
| LAN | 1 x Intel i219LM PHY Gigabit LAN (iAMT 11.0)
1 x Intel i211AT PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Connector
1 x Shared mSATA/mini-PCI Express Combo Slot (Full-size) |
| Super IO | NUVOTON NCT6116D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
OEM Option: Onboard TPM v1.2 or v2.0 |
| Back Panel Connectors |
1 3.5mm Audio connector
4 USB 3.0
2 RJ45 LAN (10/100/1000)
1 Display Port (4096 x 2304 @ 60Hz)
1 HDMI (4096 x 2304 @ 24Hz)
2 USB 2.0
1 +9V ~ +24V DC-in Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 Shared mSATA/mini-PCI Express Combo Slot (Full-size)
1 Mini-PCI Express Slot (Half-size)
6 Serial Headers (5 * RS232, 1 * RS232/422/485)
3 USB Pin Headers for up to 5 additional USB 2.0 Ports
1 40-pin eDP Header (4096 x 2304 @ 60Hz)
1 30-pin LVDS / 8-pin Inverter Header (1920 x 1080 @ 60Hz)
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 PS/2 Mouse/Keyboard Header
1 Chassis Intrusion Header
2 2-pin LAN LED Header
1 4-pin Speaker out Header with 3W Amplifier
1 5-pin SMBUS Header
1 9-pin Audio Header
1 Front Reset/Power Buttons
1 4-pin Fan Header
1 4-pin Floppy Power Output (Male)
1 2-pin +9~24V Alternate Power Connector
|
| Power Supply for NF632E |
External Power Supply – the board can be powered with a +9V ~ +24V external power supply though a DC connector on the back panel. The rear +9V ~ +24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9V ~ +24V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9V ~ +24V 2-pin power connector, where pin 1 is +9V ~ +24V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +9V ~ +24V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9V ~ +24V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Banking & Commercial
√ Digital Signage
√ AIO & Panel PC
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
√ IoT
√ HTPC
|
