| Model Name |
NF695 |
| Part Number |
JNF695HV-3455 |
JNF695L-3455 |
| Form Factor | Mini-ITX (170 x 170mm) |
| Processor | Intel® Celeron J3455 Processor Quad Core 1.50 GHz - 2.30 GHz, 10W TDP |
| Memory | 1 * 204-pin DDR3L-1866 up to 8GB total, 1.35V required |
| Graphics | Intel HD Graphics 500, 250MHz - 750MHz (J3455) |
| Audio | Realtek ALC662 HD Audio |
| LAN | 2 x Realtek RTL8111H Gigabit LAN | 1 x Realtek RTL8111H Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Connector
1 x M.2 SATA M-key 2242/2260 |
| Super IO | FINTEK F81768D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
OEM Option: Onboard TPM v1.2 or v2.0 |
| Back Panel Connectors |
| External IO |
1 12V DC-in Jack
1 VGA (1920*1200 @60)
2 RJ45 LAN (10/100/1000)
1 HDMI 1.4 (3840*2160 @30Hz)
4 USB 3.0
1 3.5mm Audio (Line out)
|
1 12V DC-in Jack
1 RJ45 LAN (10/100/1000)
2 HDMI 1.4 (3840*2160 @30Hz)
4 USB 3.0
1 3.5mm Audio (Line out)
|
| Onboard I/O Connectors |
| Internal IO |
1 SATA3 6Gb/s Connector
1 M.2 SATA 2242/2260
1 Mini PCI-E Slot (Full-size)
10 Serial Headers (1 * RS232/422/485, 9 * RS232) (2.00mm)
3 USB Headers for 6 * USB 2.0 (2.54mm)
1 24-bit Dual Channel LVDS (1920 x 1200)
1 eDP Header (2560 x 1600 60Hz or 1920 x 1400 75Hz)
1 SIM Card Socket
1 AT/ATX Mode Jumper
1 8-bit GPIO Header
1 9-pin Front Audio Header
1 5-pin SMBUS/I2C Header
1 7-pin PS/2 Header
2 4-pin Fan Header
1 4-pin Power-out Connector
1 2-pin +12V Alternate Power-in
|
1 SATA3 6Gb/s Connector
1 M.2 SATA 2242/2260
1 Mini PCI-E Slot (Full-size)
2 Serial Headers (2 * RS232) (2.00mm)
1 USB Headers for 2 * USB 2.0 (2.54mm)
1 24-bit Dual Channel LVDS (1920 x 1200)
1 eDP Header (2560 x 1600 60Hz or 1920 x 1400 75Hz)
1 AT/ATX Mode Jumper
1 8-bit GPIO Header
1 9-pin Front Audio Header
1 5-pin SMBUS/I2C Header
1 7-pin PS/2 Header
2 4-pin Fan Header
1 4-pin Power-out Connector
1 2-pin +12V Alternate Power-in
|
| Power Supply for NF695 |
External Power Supply – the board can be powered with a +12V external power supply though a locking DC connector on the back panel. The rear +12V DC jack accepts locking plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V 2-pin power connector, where pin 1 is +12V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial Computer
√ Industrial Automation/Control
√ Medical
√ AIO
√ Retail (POS/Kiosk/ATM)
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
