| Model Name | NF793 |
| Part Number | JNF793-Q170 |
| Form Factor | Mini-ITX (170 x 170mm) |
| Processor | 6th / 7th Gen Intel® Core i7 / i5 / i3 / Pentium Processor
Socket LGA 1151 (Formerly Skylake and Kaby Lake) |
| Chipset | Intel Q170 |
| Memory | 2 x 260-pin SODIMM un-buffered Dual Channel DDR4-2133 up to 32GB Total |
| Graphics | Requires Intel Core processor with Intel HD Graphics |
| Audio | Realtek ALC662VD HD Audio |
| LAN | 1 x Intel I219-LM PHY Gigabit LAN (iAMT 11.0)
1 x Intel I211-AT PCI-E Gigabit LAN |
| Storage | 4 x SATA3 6Gb/s with RAID 0, 1, 5, 10
1 x mSATA (Full-size) |
| Super IO | FINTEK F81866A |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Option: Onboard TPM v1.2 or v2.0 |
| Back Panel Connectors |
|
1 9~24V DC-in Jack (1-pin 2.5mm ID, 5.5mm OD)
3 HDMI 1.4 (4096 * 2304 @ 24Hz)
2 Serial Port (2 * RS232/422/485)
2 RJ45 LAN (10/100/1000)
4 USB 3.0
3 3.5mm Audio Jack
|
| Onboard I/O Connectors |
1 PCI-E x4 Side-Slot, Supports Jetway ETC4G & ETC4B Expansion Modules
1 mSATA Slot (Full-size)
1 Mini PCI-E Slot (Half-size)
4 SATA3 6Gb/s Connectors
1 USB Pin Headers for up to 2 additional USB 2.0 Ports (2.00mm pitch)
4 Serial Headers (4 * RS232 with 2.00mm pitch)
1 Nuvoton TPM IC onboard (for NF793T)
1 SIM Card Slot
1 Chassis Intrusion Jumper
1 AT/ATX Mode Jumper
1 8-bit GPIO Header
1 4-pin SMBUS/I2C Header
1 7-pin PS2 Keyboard Mouse Header
8 2-pin LAN LED Headers
1 9-pin Front Panel Header
2 4-pin Fan Headers
1 2-pin Internal Power connector (Molex 5566-2)
1 SATA Power connector
|
| Power Supply for NF793 |
External Power Supply – the board can be powered with a +9V ~ +24V external power supply though a DC connector on the back panel. The rear +9V ~ +24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9V ~ +24V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9V ~ +24V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +9V ~ +24V VDC. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external +9V ~ +24V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9V ~ +24V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Security & Surveillance
√ Digital Signage
√ Gaming
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
√ Networking/Storage Server/Mail Server/Print Server
√ IoT
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
