| Model |
| Brand | Supermicro |
| SYS-6026TT-HTF | SuperServer 6026TT-HTF (Black) |
| Processor/Cache |
| Motherboard | 4x Super X8DTT-HF |
| Processors | Dual 1366-pin LGA Sockets Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below: - Quad-Core Intel®
Xeon®Processor 5500 sequence (Nehalem-EP processor) NOTE: Support processors |
| QPI | up to 6.4 GT/s |
| System Memory |
| Memory Capacity | 12x 240-pin DIMM sockets Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC Registered memory Supports up to 24 GB 1333 / 1066 / 800MHz DDR3 ECC Unbuffered memory Memory Mirroring supported |
| Memory Type | 1333 / 1066 / 800MHz ECC Registered / ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Size | 1GB, 2GB, 4GB |
| Memory Voltage | 1.5 V |
| Error Detection | Corrects single-bit errors Detects double-bit errors (using ECC memory) Supports Intel® x4 and x8 Single Device Data Correction (SDDC) |
| On-Board Devices (per node) |
| Chipset | Intel® 5500 (Tylersburg) chipset ICH10R + IOH-36D |
| SATA | Intel ICH10R SATA 3.0Gbps Controller RAID 0, 1, 5, 10 support |
| IPMI | Support for Intelligent Platform Management Interface v.2.0 IPMI 2.0 with virtual media over LAN and KVM-over-LAN support Winbond® WPCM450 BMC |
| Nerwork Controllers | - Intel® 82576 Dual-Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Clock Generator | 932S421 chip |
| Graphics | Matrox G200eW 8 MB DDR2 |
| Super I/O | Winbond W83527HG chip |
| Input / Output (per node) |
| Serial ATA | Six Serial ATA ports 3 SATA hard drives supported |
| - | - |
| - | - |
| LAN | 2x RJ45 LAN ports 1x RJ45 Dedicated IPMI LAN port |
| USB | 2 rear + 1 header (2 Ports) 4 total USB ports, 2.0 Compliant / 1.1 Compliant |
| VGA | 1x VGA Port |
| Serial Port | 1 Fast UART 16550 serial port |
| System BIOS |
| BIOS Type | 32Mb SPI Flash EEPROM with AMI® BIOS |
| BIOS Features | Plug and Play (PnP) PCI 2.2 ACPI up to 3.0 USB Keyboard support |
| Chassis |
| Form Factor | 2U Rackmount |
| Model | CSE-827H-1400B |
| Dimensions |
| H x W x D | 3.5" x17.2" x28.5 " |
| Gross Weight | 85 lbs (38.6kg) |
| Front Panel |
| Buttons | Power On/Off button UID button |
| LEDs | Power LED (on power button) Network activity LED System Overheat/fan fail/power fail/ LED UID LED (on UID button) |
| Ports | - |
| Expansion Slots (per node) |
| PCI- Express | 1 (x16) PCI-E ( Low Profile) |
| - | - |
| Drive Bays (per node) |
| Hot-swap | 3x 3.5" SATA Hot-swap drive bays |
| Backplane |
| Hard Drive Backplane | 2U Hard drive Backplane |
| Peripheral Drives |
| - | - |
| - | - |
| System Cooling |
| Fans | 4x Cooling Fans |
| - | - |
| Power Supply |
| Power Supply | 1400W high-efficiency power supply with PMBus |
| AC Input | 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp |
DC Output
+5V standby | 4 Amp |
DC Output
+12V | 100 Amp @ 100-140V 116 Amp @ 180-240V |
| - | - |
| - | - |
| - | - |
